A wet pet food filler can only run as steadily as the empty cans that reach it. If pallets are broken down by hand, if layers arrive with loose dust still on the rims, or if a format change has no agreed change parts, the filling room inherits those problems. Empty-can supply is therefore a line decision, not a side purchase to be added after the filler is chosen.

This article follows empty cans from the inbound pallet to the filler infeed on a canned wet pet food line: how they arrive, how they are depalletized and single-filed, how they are cleaned without wetting the container, and what to write into the supplier brief.

Automatic empty can depalletizer and ionized cleaner with a full pallet of cans at the infeed

Describe how the cans arrive before you choose a machine

Planning empty can supply starts with the delivery pattern, not with a depalletizer catalogue. Tell the supplier how cans are palletized today, how they are protected in transit, and how the plant will stage them before a production run. Include the can format list, any variants that change diameter, height, or rim, and who is responsible for removing stretch wrap, top frames, and layer pads.

Those details set the loading position, the pallet size the lift must accept, and the space needed for incoming pallets, empty pallets, and packaging waste. A machine sized only to a headline cans-per-minute figure will not tell you whether a forklift can place a full stack without blocking the aisle, or how rejected or damaged cans leave the area.

Walk the route on a layout. Mark the unloading point, operator access, transfer conveyors, the cleaner, and the point where cans are presented to filling. Include access for replenishment, routine cleaning, and safe clearing when the filler stops. Ask the supplier to show those interfaces on the drawing rather than assuming pallet handling, inspection, or washing are included in a depalletizer package.

Depalletize one layer at a time, then single-file the cans

An automatic empty can depalletizer is built to take a palletized stack, present one layer at a time, and move those cans onto accumulation and single-filing conveyors. Coordinated automation reduces manual layer lifting and helps the filler see a continuous container supply, provided the infeed matches the pallet and the can format.

HSYL describes a pallet lift that presents layers for controlled transfer, followed by conveying that gathers and single-files the cans. A related machine, the automatic empty can and bottle depalletizer, is specified around the same task for cans or bottles: a forklift places the complete stack in the loading position, after which layer transfer, separator-sheet removal, and empty-pallet collection run under PLC control. In both cases, the brief should state the container type, the pallet pattern, and whether layer pads or top frames must be removed automatically or by hand.

Factory installation of empty can depalletizers with palletized can stacks at the loading position

Do not treat the two listings as interchangeable without checking the container range, the cleaner, and the layout. One package includes ionized-air cleaning as part of the infeed system; the other is described as a depalletizer for cans or bottles. The right choice is the one that matches the containers, the pallet, and the handoff to filling.

Clean empty cans without adding a rinse-and-dry stage

Loose dust, fibres, and handling debris on an empty can become a foreign-material problem as soon as the can reaches a meat or gravy filler. Wet pet food lines often prefer a dry clean at this point, because a water rinse would have to be followed by a drying stage before filling.

On the HSYL empty can depalletizer and ionized cleaner, ionized air is used after single-filing. The ionization step is intended to neutralize static so dust and loose debris can be released, without adding rinse water. That is a specific cleaning method, not a generic "can washer." If your process or a customer specification requires a water rinse or inversion washing, say so in the brief and treat it as a separate unit operation, with its own water, drainage, and drying requirements.

The cleaner must be sized to the can diameter and height, and it must remain effective after a format change. Ask which guides, nozzles, or change parts are needed for each can, how they are identified, and how an operator confirms that the correct set is fitted before a new SKU starts.

Plan buffers, stops, and format changes

A depalletizer that runs perfectly while the filler is running can still be a poor neighbour when the filler stops. The brief should say what happens to cans already on the conveyors: where they accumulate, what the buffer capacity is, and how operators clear a jam or a quality hold without creating a contamination or crush hazard.

For each can format, list:

  • Pallet pattern, layer pad type, and any top-frame or tray arrangement.

  • Can diameter, height, and material, plus any easy-open or special rims that affect handling.

  • The change parts or settings required, and how they are stored and identified.

  • The inspection or rejection point for dented, dirty, or fallen cans.

  • The target infeed rate at the filler, and the recovery method after a stop.

HSYL configures layout, layer handling, and the cleaner around container dimensions and changeover needs, and can integrate the system with conveying and filling as one front-end. That integration only works if the can list and the operating method are written down first.

Food and beverage production line conveyors transferring cans between process stages

What the project documents should include

Ask for a layout that shows pallet staging, the depalletizer, pad and pallet discharge, the cleaner, single-filers, and the filler infeed. The document set should also cover utilities, guarding, access for cleaning, spare and change parts, and the tests that will be run with representative cans and pallets, not with a single display stack.

If empty-can inspection, coding, or a water rinse is required, state whether each item is included or excluded. Do not assume those tasks are part of a depalletizer quotation.

If the same plant also fills trays or pouches on another route, keep the empty-can path documented as its own line. A tray denester or a pouch magazine is not a substitute for a can depalletizer, and a shared forklift aisle is not a shared infeed specification. State which formats share the depalletizer, which have a dedicated infeed, and how change parts are kept apart so a pouch or tray change does not leave the can cleaner mis-set.

The takeaway

Treat empty-can supply as the first controlled step of the wet pet food canning line. Describe how cans arrive, depalletize them in controlled layers, single-file them, and clean them in a way that matches the filler. Write format changes, buffers, and the supplier handoff into the brief, so the filling room is not left to invent an infeed after the machines are already on the floor.