A can of wet cat or dog food is only shelf-stable if two things go right: the retort process must reach commercial sterility, and the can must stay sealed afterwards. The second part depends on a few millimetres of folded metal at the top of the can, the double seam. If that seam is poorly formed, a correct sterilization process can still be undone by a leak during cooling, storage or transport.
This article explains how a double seam is formed on a pet food can, why closure checks are a routine part of production, and what to agree with an equipment supplier before the seamer is installed.
Where seaming sits in a pet food canning line
On a typical wet pet food canning line, meat is ground or emulsified, formed and cooked into chunks or pâté, dosed into cans, closed, and then sterilized in a retort. HSYL's line page places the closing step directly after filling: synchronized 4-, 6- or 8-head seamers remove headspace air with steam or vacuum and then form a hermetic double seam on the can.
Because the seamer sits between filling and the retort, problems from both directions show up there. Product splashed on the flange during filling affects the seam. A seam that is out of specification is not corrected by the retort; it can make the retort cycle harder on the can.
How a double seam is formed
A double seam joins the can end (the lid) to the flange of the can body. The can and end are held under a seaming chuck, and two sets of rolls do the work:
- 1.
First operation roll. It curls the edge of the end and the body flange together so the two hooks interlock.
- 2.
Second operation roll. It flattens and tightens that interlocked fold into the finished seam, compressing the sealing compound in the end.
The result is five layers of metal folded together: the end's cover hook interlocks with the can's body hook. Format-specific chucks, rolls and change parts are matched to each can and end combination.
Vacuum or steam-flow: controlling the headspace
Wet pet food is filled hot or warm and leaves some headspace under the lid. How that headspace is treated at closing affects residual oxygen, can vacuum and how the can behaves in the retort. A can seamer for this application usually offers vacuum closing, steam-flow closing, or another validated arrangement. HSYL describes these as different headspace-control methods, with the right choice depending on the product, fill temperature, container and target residual oxygen or vacuum. There is no single answer for every recipe: a fine pâté and a chunks-in-gravy product can behave very differently under the lid.
What the regulations ask for
For the US market, low-acid canned pet food falls under the same container-closure rules as low-acid canned human food. FDA regulation 21 CFR 500.23 states that parts 507 and 113 apply to low-acid foods in hermetically sealed containers intended for animals. Section 113.60 then sets out closure checks:
Visual examination. A qualified closure inspector examines the top seam of a can randomly selected from each seaming head, looking for defects such as cutover or sharpness, skidding or deadheading, false seam, and droop at the crossover. The regulation says these checks should be made at intervals not exceeding 30 minutes, and again after a jam, a machine adjustment, or a restart after a long stop.
Teardown examination. A qualified person tears down cans from each seaming station and measures the seam. The interval should not exceed 4 hours. With a micrometer, the required measurements are cover hook, body hook, width, tightness (observed as wrinkle) and thickness. With a seam scope or projector, body hook, overlap, tightness and thickness are required.
Records and corrective action. Observations, measurements and any corrective action are recorded.
Other markets have their own requirements, so the factory's quality team should confirm which rules apply to each destination.
External checks and teardown are not interchangeable
A seam can look correct from outside and still fall short inside. External examination shows visible defects and container condition. Teardown shows how far the hooks overlap and how tight the seam is. One does not replace the other, and a good-looking seam is not proof that the internal measurements pass.
Two practical points follow from this:
Record per seaming head. Note the can and end references, the seamer and head or station, and the sample time. A measurement without that identity is hard to use in an investigation.
Don't average away a bad result. Keep individual results visible. An average can hide the one head that is drifting.
Use the can maker's limits, not generic numbers
Seam dimensions are not universal. The acceptance limits for body hook, cover hook, overlap, width and thickness come from the can and end supplier for that specific combination. HSYL's seamer selection guide advises against copying generic seam figures into an RFQ. Use the criteria confirmed for the actual package by the can supplier and the factory's quality team.
What to agree before ordering a seamer
When buying or upgrading closing equipment for a pet food line, put these points in writing:
- 1.
Package drawings. Current drawings for every can and end, and which combinations the supplier has reviewed.
- 2.
Change parts. Tooling for each format, and the checks required after a format change. A test on one can size does not qualify the others.
- 3.
Inspection method. Who supplies the seam tools, who performs teardown, how samples are chosen and how results are recorded.
- 4.
Product trial. Run real product and real cans, and record the setup and closure results.
- 5.
Interfaces. How filled cans arrive at the seamer, how the flange is kept clean, and access for inspection and cleaning.
- 6.
Training. Seam teardown training and documentation for the closure inspectors.
Summary
The double seam is the part of a pet food can that keeps the retort's work intact. It is formed in two roll operations, its headspace treatment is chosen for the recipe, and it is checked visually and by teardown at regular intervals against limits supplied by the can maker. Plan the seamer, the inspection method and the records together, and the closure becomes a controlled step rather than an assumption.